 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 74LVC2G66 Bilateral switch Rev. 01 -- 29 June 2004 Product data sheet 1. General description The 74LVC2G66 is a high-performance, low-power, low-voltage, Si-gate CMOS device. The 74LVC2G66 provides two analog switches. Each switch has a input and output (pins Y and Z) and an active HIGH enable input (pin E). When pin E is LOW, the analog switch is turned off. 2. Features s Wide supply voltage range from 1.65 V to 5.5 V s Very low ON-resistance: x 7.5 (typical) at VCC = 2.7 V x 6.5 (typical) at VCC = 3.3 V x 6 (typical) at VCC = 5 V. s High noise immunity s Complies with JEDEC standard: x JESD8-7 (1.65 V to 1.95 V) x JESD8-5 (2.3 V to 2.7 V) x JESD8-B/JESD36 (2.7 V to 3.6 V). s ESD protection: x HBM EIA/JESD22-A114-B exceeds 2000 V x MM EIA/JESD22-A115-A exceeds 200 V. s CMOS low-power consumption s Latch-up performance meets requirements of JESD78 Class I s Direct interface with TTL levels s Enable inputs accept voltages up to 5 V s SOT505-2 and SOT765-1 package s Specified from -40 C to +85 C and -40 C to +125 C. 3. Quick reference data Table 1: Quick reference data GND = 0 V; Tamb = 25 C; tr = tf 2.5 ns. Symbol Parameter Conditions CL = 50 pF; RL = 500 VCC = 3 V VCC = 5 V 2.4 1.8 ns ns Min Typ Max Unit tPZH, tPZL turn-on time nE to VOS Philips Semiconductors 74LVC2G66 Bilateral switch Table 1: Quick reference data ...continued GND = 0 V; Tamb = 25 C; tr = tf 2.5 ns. Symbol Parameter Conditions CL = 50 pF; RL = 500 VCC = 3 V VCC = 5 V CI CS CPD enable input capacitance switch capacitance OFF-state ON-state power dissipation capacitance CL = 50 pF; fi = 10 MHz; VCC = 3.3 V CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N + {(CL + CS) x VCC2 x fo} where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; CS = switch capacitance in pF; VCC = supply voltage in V; N = total load switching outputs. The condition is VI = GND to VCC. [1] [2] Min Typ Max Unit 3.0 2.2 2.0 5 9.5 ns ns pF pF pF pF tPHZ, tPLZ turn-off time nE to VOS 11.0 - [1] [2] 4. Ordering information Table 2: Ordering information Package Temperature range Name 74LVC2G66DP 74LVC2G66DC -40 C to +125 C -40 C to +125 C TSSOP8 VSSOP8 Description Version plastic thin shrink small outline package; 8 leads; SOT505-2 body width 3 mm; lead length 0.5 mm plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 Type number 5. Marking Table 3: Marking Marking code V66 V66 Type number 74LVC2G66DP 74LVC2G66DC 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 2 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 6. Functional diagram 1Y 1Z 1 7# 1 1 X1 2 1E 5 1 1 X1 001aaa531 6 2Z 2Y 3# 2E 001aaa530 Fig 1. Logic symbol. Fig 2. IEC logic symbol. Z Y E VCC 001aaa532 Fig 3. Logic diagram (one switch). 7. Pinning information 7.1 Pinning 1Z 1Y 2E GND 1 2 3 4 001aaa529 8 VCC 1E 2Y 2Z 66 7 6 5 Fig 4. Pin configuration. 7.2 Pin description Table 4: Symbol 1Y 1Z 2E GND 2Y 9397 750 13259 Pin description Pin 1 2 3 4 5 Description independent input or output independent input or output enable input (active HIGH) ground (0 V) independent input or output (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 3 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Pin description ...continued Pin 6 7 8 Description independent input or output enable input (active HIGH) supply voltage Table 4: Symbol 2Z 1E VCC 8. Functional description 8.1 Function table Table 5: Input E L H [1] H = HIGH voltage level; L = LOW voltage level. Function table [1] Switch OFF-state ON-state 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC VI IIK ISK VS IS ICC, IGND Tstg Ptot [1] Parameter supply voltage input voltage input diode current switch diode current DC switch voltage range switch source or sink current VCC or GND current storage temperature power dissipation Conditions [1] Min -0.5 -0.5 -0.5 -65 Max +6.5 +6.5 -50 50 VCC + 0.5 50 100 +150 300 Unit V V mA mA V mA mA C mW VI < -0.5 V or VI > VCC + 0.5 V VI < -0.5 V or VI > VCC + 0.5 V enable and disable mode VS > -0.5 V or VS < VCC + 0.5 V Tamb = -40 C to +125 C - The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 7: VCC VI VS Recommended operating conditions Conditions Min 1.65 0 [1] [2] Symbol Parameter supply voltage input voltage Typ - Max 5.5 5.5 VCC Unit V V V DC switch voltage range enable and disable mode 0 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 4 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Recommended operating conditions ...continued Conditions Min -40 VCC = 1.65 V to 2.7 V VCC = 2.7 V to 5.5 V [3] [3] Table 7: Tamb tr, tf Symbol Parameter operating ambient temperature input rise and fall times Typ - Max +125 20 10 Unit C ns/V ns/V 0 0 [1] To avoid drawing VCC current out of terminal nZ, when switch current flows in terminal nY, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no VCC current will flow out of terminal nY. In this case there is no limit for the voltage drop across the switch. For overvoltage tolerant switch voltage capability, see the 74LVCV2G66. Applies to control signal levels. [2] [3] 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VIH Parameter C [1] VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V VIL LOW-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) IS(ON) ICC ICC input leakage current on control pin analog switch OFF-state current analog switch ON-state current quiescent supply current additional quiescent supply current per control pin input capacitance switch capacitance OFF-state ON-state Tamb = -40 C to +125 C VIH HIGH-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V 0.65 x VCC 1.7 2.0 0.7 x VCC V V V V VI = 5.5 V or GND; VCC = 5.5 V VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 5 VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 6 VI = VCC or GND; VS = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 0.6 V; VS = GND or VCC; IO = 0 A; VCC = 5.5 V 0.65 x VCC 1.7 2.0 0.7 x VCC 0.1 0.1 0.1 0.1 5 0.7 0.8 0.3 x VCC 5 5 5 10 500 V V V V V V V A A A A A HIGH-level input voltage Conditions Min Typ Max Unit Tamb = -40 C to +85 0.35 x VCC V CI CS - 2.0 5 9.5 - pF pF pF 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 5 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Table 8: Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VIL Parameter LOW-level input voltage Conditions VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) IS(ON) ICC ICC input leakage current on control pin analog switch OFF-state current analog switch ON-state current quiescent supply current additional quiescent supply current per control pin VI = 5.5 V or GND; VCC = 5.5 V VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 5 VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 6 VI = VCC or GND; VS = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 0.6 V; VS = GND or VCC; IO = 0 A; VCC = 5.5 V Min Typ Max 0.7 0.8 0.3 x VCC 100 200 200 200 5000 Unit V V V A A A A A 0.35 x VCC V [1] All typical values are measured at Tamb = 25 C. VCC VIL IS E Y Z VIH IS VO GND 001aaa534 VCC E Z Y IS VI VI GND VO 001aaa535 VI = VCC or GND and VO = GND or VCC. VI = VCC or GND and VO = open circuit. Fig 5. Test circuit for measuring switch OFF-state current. Fig 6. Test circuit for measuring switch ON-state current. Table 9: Resistance RON At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit Figure 7. Symbol RON(peak) Parameter switch ON-state resistance (peak) Conditions VS = GND to VCC; VI = VIH IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V [1] Min Typ Max Unit Tamb = -40 C to +85 C 35 14 11.5 8.5 6.5 100 30 25 20 15 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 6 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Table 9: Resistance RON ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit Figure 7. Symbol RON(rail) Parameter switch ON-state resistance (rail) Conditions VS = GND; VI = VIH IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VS = VCC; VI = VIH IS = 4 mA; VCC = 1.65 to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(flat) switch ON-state resistance (flatness) VS = GND to VCC; VI = VIH; see Figure 9 to Figure 13 IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V Tamb = -40 C to +125 C RON(peak) switch ON-state resistance (peak) VS = GND to VCC; VI = VIH IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(rail) switch ON-state resistance (rail) VS = GND; VI = VIH IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VS = VCC; VI = VIH IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V [1] [2] These typical values are measured at Tamb = 25 C and nominal VCC. These typical values are measured at Tamb = -40 C to +85 C and nominal VCC. (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Min [1] Typ 10 8.5 7.5 6.5 6 12 8.5 7.5 6.5 6 Max 30 20 18 15 10 30 20 18 15 10 Unit [2] - 100 17 10 5 3 - - - 150 45 38 30 23 45 30 27 23 15 45 30 27 23 15 9397 750 13259 Product data sheet Rev. 01 -- 29 June 2004 7 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 40 RON () 30 VS VCC 20 VIH E Z Y (2) 001aaa707 (1) IS 10 (3) (4) (5) VI GND 001aaa533 0 0 1 2 3 4 VI (V) 5 VI = GND to VCC. (1) VCC = 1.8 V. (2) VCC = 2.5 V. (3) VCC = 2.7 V. (4) VCC = 3.3 V. (5) VCC = 5.0 V. Measured at Tamb = 25 C. Fig 7. Test circuit for measuring switch ON-resistance. Fig 8. Typical switch ON-resistance as a function of input voltage; VS = GND to VCC. 80 RON () 60 001aaa712 16 RON () 12 (1) (2) 001aaa708 40 8 (3) (4) 20 (1) (2) (3) (4) 4 0 0 1 2 3 4 VI (V) 5 0 0 1 2 3 4 VI (V) 5 (1) Tamb = 125 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (4) Tamb = -40 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (4) Tamb = -40 C. Fig 9. Switch ON-resistance as a function of input voltage; VCC = 1.8 V. Fig 10. Switch ON-resistance as a function of input voltage; VCC = 2.5 V. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 8 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 16 RON () 12 (1) (2) 001aaa709 16 RON () 12 001aaa710 8 (3) (4) 8 (1) (2) (3) 4 4 (4) 0 0 1 2 3 4 VI (V) 5 0 0 1 2 3 4 VI (V) 5 (1) Tamb = 125 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (4) Tamb = -40 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (4) Tamb = -40 C. Fig 11. Switch ON-resistance as a function of input voltage; VCC = 2.7 V. Fig 12. Switch ON-resistance as a function of input voltage; VCC = 3.3 V. 16 RON () 12 001aaa711 8 4 (1) (2) (3) (4) 0 0 1 2 3 4 VI (V) 5 (1) Tamb = 125 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (4) Tamb = -40 C. Fig 13. Switch ON-resistance as a function of input voltage; VCC = 5.0 V. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 9 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 12. Dynamic characteristics Table 10: Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 16. Symbol tPHL, tPLH Parameter C [1] see Figure 14 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPZH, tPZL turn-on time nE to VOS see Figure 15 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPHZ, tPLZ turn-off time nE to VOS see Figure 15 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to V 5.5 V CPD power dissipation capacitance fi = 10 MHz VCC = 2.5 V VCC = 3.3 V VCC = 5.0 V Tamb = -40 C to +125 C tPHL, tPLH propagation delay nY to nZ or nZ to nY see Figure 14 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPZH, tPZL turn-on time nE to VOS see Figure 15 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 1.0 1.0 1.0 1.0 1.0 13.0 7.5 6.5 6.0 5.0 ns ns ns ns ns 3.0 2.0 1.5 1.5 1.0 ns ns ns ns ns [2] [3] Conditions Min Typ Max Unit Tamb = -40 C to +85 propagation delay nY to nZ or nZ to nY 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 - 0.8 0.4 0.4 0.3 0.2 4.6 2.7 2.7 2.4 1.8 3.8 2.1 3.5 3.0 2.2 9.0 11.0 15.7 2 1.2 1 0.8 0.6 10 5.6 5.0 4.4 3.9 9.0 5.5 6.5 6.0 5.0 - ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns pF pF pF 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 10 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Table 10: Dynamic characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 16. Symbol tPHZ, tPLZ Parameter turn-off time nE to VOS Conditions see Figure 15 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V [1] [2] All typical values are measured at Tamb = 25 C and nominal VCC. CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N + {(CL + CS) x VCC2 x fo} where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = total load switching outputs; CS = switch capacitance. The condition is VI = GND to VCC. Min 1.0 1.0 1.0 1.0 1.0 Typ - Max 11.5 7.0 8.5 8.0 6.5 Unit ns ns ns ns ns [3] 13. Waveforms VI nY or nZ input GND t PLH VOH nZ or nY output VOL 001aaa541 VM VM t PHL VM VM Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 14. The input (nY, nZ) to output (nZ, nY) propagation delays and the output transition times. Table 11: VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Supply voltage 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 11 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch VI nE input GND t PLZ VCC nY or nZ output LOW-to-OFF OFF-to-LOW VOL t PHZ output HIGH-to-OFF OFF-to-HIGH VOH Vy VM GND switch enabled switch disabled switch enabled 001aaa542 VM t PZL VM VX t PZH nY or nZ Measurement points are given in Table 12. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 15. The turn-on and turn-off times. Table 12: VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC VX VOL + 0.1 x VCC VOL + 0.1 x VCC VOL + 0.3 V VOL + 0.3 V VOL + 0.3 V VY VOH - 0.1 x VCC VOH - 0.1 x VCC VOH - 0.3 V VOH - 0.3 V VOH - 0.3 V Supply voltage VEXT VCC PULSE GENERATOR VI D.U.T. RT CL RL VO RL mna616 Test data is given in Table 13. Definitions test circuit: RL = Load resistor. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = Test voltage for switching times. Fig 16. Load circuitry for switching times. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 12 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Test data Input VI VCC VCC 2.7 V 2.7 V VCC tr, tf 2.0 ns 2.0 ns 2.5 ns 2.5 ns 2.5 ns Load CL 30 pF 30 pF 50 pF 50 pF 50 pF RL 1 k 500 500 500 500 VEXT tPLH, tPHL open open open open open tPZH, tPHZ GND GND GND GND GND tPZL, tPLZ 2 x VCC 2 x VCC 6V 6V 2 x VCC Table 13: VCC Supply voltage 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V 14. Additional dynamic characteristics Table 14: Additional dynamic characteristics At recommended conditions; typical values measured at Tamb = 25 C. Symbol dsin Parameter sine-wave distortion Conditions RL = 10 k; CL = 50 pF; fi = 1 kHz; see Figure 17 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V RL = 10 k; CL = 50 pF; fi = 10 kHz; see Figure 17 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V fON-state(res) switch ON-state signal frequency response RL = 600 ; CL = 50 pF; see Figure 18 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V RL = 50 ; CL = 5 pF; see Figure 18 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V [1] [1] Min Typ Max Unit - 0.032 0.008 0.006 0.005 - % % % % - 0.068 0.009 0.008 0.006 135 145 150 155 >500 >500 >500 >500 - % % % % MHz MHz MHz MHz MHz MHz MHz MHz 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 13 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch Table 14: Additional dynamic characteristics ...continued At recommended conditions; typical values measured at Tamb = 25 C. Symbol OFF(ft) Parameter Conditions [2] Min Typ Max Unit switch OFF-state signal RL = 600 ; CL = 50 pF; fi = 1 MHz; feed-through see Figure 19 attenuation VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 19 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V [2] -46 -46 -46 -46 - dB dB dB dB - -37 -37 -37 -37 - dB dB dB dB Vct(cti-sw) crosstalk between control input to signal output RL = 600 ; CL = 50 pF; fi = 1 MHz; tr = tf = 2 ns; see Figure 20 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V 91 119 205 mV mV mV mV Vct(sw-sw) crosstalk between switches RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 21 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 21 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V [1] - -56 -56 -56 - dB dB dB dB -29 -28 -28 200 350 410 440 - dB dB dB dB MHz MHz MHz MHz fmax frequency response (-3 dB) RL = 50 ; CL = 10 pF; see Figure 18 VCC = 1.65 V VCC = 2.3 V VCC = 3 V VCC = 4.5 V [3] Q charge injection CL = 0.1 nF; Vgen = 0 V; Rgen = 0 ; fi = 1 MHz; RL = 1 M; see Figure 22 VCC = 3.5 V VCC = 5.5 V - 0.003 0.0035 - pC pC [1] [2] [3] Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads -3 dB. Adjust fi voltage to obtain 0 dBm level at input. Guaranteed by design. (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 13259 Product data sheet Rev. 01 -- 29 June 2004 14 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 0.5VCC VCC RL VIH E Z or Y 10 F Y or Z fi 600 CL D GND 001aaa544 Test conditions: VCC = 1.65 V: Vi = 1.4 V (p-p). VCC = 2.3 V: Vi = 2 V (p-p). VCC = 3 V: Vi = 2.5 V (p-p). VCC = 4 V: Vi = 4 V (p-p). Fig 17. Test circuit for measuring sine-wave distortion. 0.5VCC VCC RL VIH 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa543 Fig 18. Test circuit for measuring the frequency response when switch is in ON-state. 0.5VCC VCC RL 0.5VCC RL VIL 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa545 Fig 19. Test circuit for measuring feed-through attenuation when switch is in OFF-state. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 15 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 0.5VCC Ri = 600 0.5VCC VCC E RL = 600 Y or Z Z or Y logic input 50 CL = 50 pF VO GND 001aaa546 Fig 20. Test circuit for measuring crosstalk between control input and output. 0.5VCC VIH 0.1 F 1E Ri 600 RL 1Y or 1Z 1Z or 1Y CL 50 pF fi 50 VO1 channel ON 0.5VCC VIL 2E 2Y or 2Z Ri 600 RL 2Z or 2Y CL 50 pF VO2 channel OFF 001aaa547 20 log10 (VO2/VO1) or 20 log10 (VO1/VO2). Fig 21. Test circuit for measuring crosstalk between switches. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 16 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch VCC E Y or Z Rgen logic input Vgen GND 001aaa548 RL = 1 M CL = 0.1 nF Z or Y VO logic (E) off input on off VO VOUT 001aaa549 Q = (VOUT) x (CL). Fig 22. Test circuit for measuring injection charge. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 17 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 15. Package outline TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 D E A X c y HE vMA Z 8 5 A pin 1 index A2 A1 (A3) Lp L 1 e bp 4 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.00 A2 0.95 0.75 A3 0.25 bp 0.38 0.22 c 0.18 0.08 D(1) 3.1 2.9 E(1) 3.1 2.9 e 0.65 HE 4.1 3.9 L 0.5 Lp 0.47 0.33 v 0.2 w 0.13 y 0.1 Z(1) 0.70 0.35 8 0 Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT505-2 REFERENCES IEC JEDEC --JEITA EUROPEAN PROJECTION ISSUE DATE 02-01-16 Fig 23. Package outline TSSOP8. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 18 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 D E A X c y HE vMA Z 8 5 Q A pin 1 index A2 A1 (A3) Lp L 1 e bp 4 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1 A1 0.15 0.00 A2 0.85 0.60 A3 0.12 bp 0.27 0.17 c 0.23 0.08 D(1) 2.1 1.9 E(2) 2.4 2.2 e 0.5 HE 3.2 3.0 L 0.4 Lp 0.40 0.15 Q 0.21 0.19 v 0.2 w 0.13 y 0.1 Z(1) 0.4 0.1 8 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT765-1 REFERENCES IEC JEDEC MO-187 JEITA EUROPEAN PROJECTION ISSUE DATE 02-06-07 Fig 24. Package outline VSSOP8. 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 19 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 16. Revision history Table 15: Revision history Release date 20040629 Data sheet status Product data sheet Change notice Order number 9397 750 13259 Supersedes Document ID 74LVC2G66_1 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 20 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 17. Data sheet status Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 18. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 19. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 20. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com 9397 750 13259 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 29 June 2004 21 of 22 Philips Semiconductors 74LVC2G66 Bilateral switch 21. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 21 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contact information . . . . . . . . . . . . . . . . . . . . 21 (c) Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 29 June 2004 Document order number: 9397 750 13259 Published in The Netherlands |
Price & Availability of 74LVC2G66DP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |